PLC manufacturer independent PLC Trainer
Content: PLC manufacturer independent:
PLC manufacturer independent
PLC training system can be used with all PLC controls
The Lab4PLC systems can be used with different PLC controls. The use of a Siemens logo! 8, Siemens Simatic S7-300, S7-1200 or S7-1500 is just as possible as a Controllino or PLC control of other manufacturers. On this page, you will find a selection of possible PLC manufacturers, PLC controllers and requirements for PLC controllers.
A change of the PLC control is possible at any time and at short notice.
A change of the PLC control is possible at any time and at short notice.
PLC manufacturer independent: all common PLC controls* can be used
The Lab4PLC supports all common PLC controls* available on the market, e.g.
* PLC controls with 12 or 24 Volt operating voltage
- Siemens PLC: Siemens Logo! 8, Siemens Simatic S7-300, S7-1200, S7-1500, iot-2000, etc.
- Controllino PLC: Mini, Mega, Maxi, Automation, MYPLC
- Bosch Rexroth PLC
- Schneider PLC
- Mitsubishi PLC
- Beckhoff PLC
- Allen Bradley PLC
- and many more!
* PLC controls with 12 or 24 Volt operating voltage
Flexible use of the desired development environment
Use the development environment supported or preferred by your PLC.- CODESYS
- Siemens Simatic Step 7
- Tia Portal
- Simatic Manager7
- Wincc
Flexible support of all protocols!
The Lab4PLC supports all available protocols- Profinet
- Feldbus
- and many more
Requirements for the PLC control system
Operating voltage for Lab4PLC suitable PLC controls
The Lab4PLC systems are suitable for PLC controls with an operating voltage of 12 or 24 volts.
Please note that all Lab4PLC systems are supplied without PLC control.
The professional installation and wiring of the PLC control is the responsibility of the customer.
Select Lab4PLC Model
The Lab4PLC models differ in
- the size of the mounting surface for the used PLC control and
- the maximum usable number of digital or analog inputs and outputs.
Lab4PLC Mini (PLUS): the right choice for small PLC controllers
The Lab4PLC Mini and Lab4PLC Mini PLUS are suitable for small PLC controllers. The maximum mounting surface of the PLC control is width=170 mm x depth=115 mm.Of course, small PLC controllers can also be used with the Lab4PLC Basic (PLUS) or Lab4PLC Advanced (PLUS).
| System: |
◄ Lab4PLC Mini ► ◄ Lab4PLC Mini PLUS ► |
||||||||
| SPS Manufacturer: |
Controllino, Siemens Logo! 8, Siemens Simatic, Beckhoff, Bosch Rexroth, Phoenix Contact, Eaton, Schneider, Moeller and many more!
> Suitable for small PLC controls
> Operating voltage of 12 or 24 volts
> max. mounting surface: W=170 mm x D=115
|
||||||||
| Number I/O | Maximum number of inputs and outputs
|
Lab4PLC Basic/Advanced (PLUS): the right choice for all PLC controls
Lab4PLC Basic (PLUS) or Lab4PLC Advanced (PLUS) are suitable for all PLC controls. Of course, small PLC controls can be also used.
The maximum mounting surface of the PLC control is width=170 mm x depth=115 mm.
The maximum mounting surface of the PLC control is width=170 mm x depth=115 mm.
- With the Lab4PLC Basic (PLUS) or Lab4PLC Advanced (PLUS) you are always on the right side.
- A later change of the PLC manufacturer and/or the PLC control is possible at any time and at short notice.
| System: |
◄ Lab4PLC Basic ► ◄ Lab4PLC Basic PLUS ► ◄ Lab4PLC Advanced ► ◄ Lab4PLC Advanced PLUS ► |
||||||||
| SPS Manufacturer: |
Controllino, Siemens Simatic z. B. S7-300, S7-1200, S7-1500, Beckhoff, Bosch Rexroth, Phoenix Contact, Eaton, Schneider, Moeller and many more!
> Suitable for all PLC controls (also small PLC controls)
> Operating voltage of 12 or 24 volts
>max. mounting surface: W=380 mm x D=205 mm
|
||||||||
| Number I/O | maximum number of inputs and outputs
|
* PLC controls with 12 or 24 Volt operating voltage
