The
easy-Trainingsboard is suitable for EATON easyE4 training and further education for learning, testing and simulating. A PLC program created with EATON easySoft is transferred to the easyE4 for this purpose. On the
easy-Trainingsboard, every function of the PLC program can now be simulated and tested in detail with a wide variety of sensors and actuators.
Ideal for
IHK exam preparation or for
"learning by doing"
The PLC didactic exercises with training cards / learning cards included in the scope of delivery support you from the creation of an easySoft program to testing and checking the functions. For this purpose, the available sensors can be switched on or off as required on the
easy-Trainingsboard. Thus up to 8 push/latch switches, 4 analog value transmitters (0-10Volt) and/or one pulse transmitter (2-1000 Hz, linear) are available. 4 LEDs and a buzzer serve as actuators.
With a
PLC-Extension module 8TE1/8RE1 (not included in the scope of delivery), 4 additional outputs with LEDs can be used on the
easy-Trainingsboard.
An overview of all easy-Trainingsboard Sets can be found
here!
Technical data:
Sensors/Input
8 push button / latching switch for simulation of input signals
(to be used as switches or buttons, simulating break contact or closing contact)
4 analog inputs for simulation of analog sensors with 0-10 volt
(The analog inputs can be alternatively connected via 4 switches to the easyE4 inputs)
1 pulse generator to simulate the fast counter inputs
(The pulse generator can be alternatively connected via a switch to an easyE4 input)
Actuators/Outputs
8 LEDs indicating status of the outputs
4 LEDs are connected with the easyE4
4 more LEDs can be used with a "PLC-Extension Module 8TE1/8RE1" (can be ordered separately)
1 signal transmitter
The signal transmitter can be switched on alternatively to an easyE4 output
Additionally
1 placeholder for Trainingscards
Training Cards illustrate the use of sensors and actuators.
1 power supply
The easy-Trainingsboard can be operated with voltages between 12 ... 24 V DC.
1 LED for voltage monitoring
the LED indicates a sufficient power supply in the range of 12... 24 volt
1 interface connector 40 pin
for connecting "Interface modules", for example, Traffic Light or "Interface Module 1"
Connectors for the connection of "PLC-Extension Modules for 8TE1/8RE1 or 6AE1"
("PLC-Extension Modules" are connected to the easy-Trainingsboard on the right side and secured with screws)
1 voltage output for supplying an external display
(the power supply of "easy-Trainingsboard" has to be selected accordingly)
The
easy-Trainingsboard is mounted on an aluminum bracket.
Note
The
easy-Trainingsboard is suitable for the following PLC / SPS:
EATON EasyE4 UC-12RC1 (manufacturer number: 197211)
or
EATON EasyE4 DC-12TC1 (manufacturer number: 197213)
The
easy-Trainingsboard can be operated with a power supply between 12... 24 volt
please observe in any case the required voltage for which "PLC-Extension Modules for 8TE1/8RE1 or 6AE1" or any third-party models.
Scope of delivery
easy-Trainingsboard mounted on aluminum bracket
size with aluminium bracket and easyE4 Module: (L x W x H) approx. 250 x 170 x 110 mm
Set of cables for wiring the Module easyE4
Note: The easyE4 is not included in the delivery!
Plug power supply
universal input 90-264 VAC, output 24V/1A, 24 Watt, high efficiency and low StandBy consumption, overload and short-circuit protected
USB stick contains
technical manual as PDF
didactic Task descriptions as PDF
Sample solutions as an easySoft contact plan, approximately 40 pieces
(Partially a Trainingscard contains multiple tasks or there are several solutions for a task)
30 training cards
suitable for the task descriptions, tasks divided into 3 levels of difficulty
Attention
The "
easy-Trainingsboard" comes without easyE4 Module
